Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Cap & Crown for Oak Cliff Homeowners
If your chimney cap is rusted through, bent off its base, or missing entirely, the flue is open to whatever Oak Cliff weather and wildlife send down it. Rainwater runs straight into the smoke chamber, squirrels and birds nest in the flue, and the cast crown below it starts cracking with every wet spell and hot burn cycle. Our technicians have up to 12 years of experience and carry caps and crowns sourced from Gelco and Famco, so we can usually handle the whole repair same-day. We’ll tell you exactly what we found and what it means before we quote a repair. Call (888) 847-8540. We answer 24/7, with fast dispatch from 7am to 7pm.
What Our Chimney Cap & Crown Service Includes
Cap and crown work is one system even though it’s two parts. The cap keeps water and animals out of the flue; the crown sheds water off the top of the masonry so it doesn’t soak into the brick and mortar below. We treat them together because a new cap over a failing crown just moves the leak down a few inches.
Cap Installation
A chimney cap is a metal hood that sits over the flue opening on legs or a mesh body, sized to the flue and secured through the crown. You need one when the flue is open, when you’ve just had a liner installed, or when the old cap pulled loose in wind. We measure the flue, match the cap to the liner type, and fasten it so it doesn’t rattle or shift.

Cap Replacement
Replacement is for caps that have rusted through, warped, or lost their mesh screens to corrosion. A holed cap lets water in; a screenless cap lets birds and squirrels drop nesting material straight into the flue. We pull the old cap, check the flue tile and crown underneath for damage the failing cap may have allowed, and fit a new one from our Gelco and Famco lines.

Crown Repair
The crown is the sloped masonry or concrete cap at the very top of the chimney, and it’s what keeps water out of the brick below. Cracks, spalling, or a crown that has pulled away from the flue tile needs repair before water ruins the structure. We rebuild failing crowns to a proper slope and bond them to the flue so water runs off instead of sitting.

Crown Coating
Crown coating is a flexible sealant membrane applied over a crown that’s cracked but still structurally sound. It’s a good fit when the masonry is intact but the surface is checking and letting water in at the seams. Coating is cheaper than a rebuild and buys years of service, and we’ll tell you honestly when coating is enough and when it isn’t.
Multi-Flue Cap
A multi-flue cap covers two or more flues on a single chimney with one top-mounted hood, which looks cleaner than a cluster of individual caps. It’s common on Oak Cliff homes with a fireplace flue plus a furnace or water heater flue in the same stack. We build these to fit the actual footprint of your chimney top, with screened sides for ventilation.
Custom Cap
Some chimneys have oversized flues, irregular shapes, or a stack that a standard cap won’t fit properly. A custom cap is fabricated to the exact dimensions of your flue and crown instead of forced to fit with adapters. We take measurements on site, and because we work with Copperfield and Olympia Chimney product lines, we can spec components that most local competitors have to special-order.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Cap & Crown
We work with Gelco and Famco cap and crown products because they’re what professionals specify rather than what’s cheapest to stock. Both lines are built for real weather exposure, with heavier gauge metal and proper screened bodies, which is why we use them on Oak Cliff roofs instead of generic hardware-store caps that rust out in a few seasons. We also work with Copperfield components when a job calls for a specific fit.
On the liner side, we use DuraFlex flexible liner systems and HeatShield ceramic resurfacing, and cap work often uncovers a flue that needs one or the other once we’re up top. We’ll tell you exactly what we found and what it means before we quote. Whether you have Gelco, Famco, Copperfield, or any other make, we can help.
Signs You Need Chimney Cap & Crown Right Now
- The cap is rusted, bent, or gone. Rust perforation or a missing cap leaves the flue open to rain and animals, and water in the smoke chamber is the start of a much bigger repair. If you can see daylight down the flue, call us.
- Birds, squirrels, or wasps in the firebox. Animals nesting in an uncapped flue block the draft and create a fire hazard when nesting material piles up near the damper. A screened cap solves it.
- Cracks in the crown or a crumbling top. Visible cracks, flaking concrete, or a crown separating from the flue tile mean water is getting into the masonry. This one gets worse every rainy season, so it’s worth handling early.
- Water stains on the ceiling or smoke chamber walls. Damp patches near the chimney chase or a musty smell after rain point to a failing crown or cap seal. Fixing the top is almost always cheaper than repairing the damage below.
- Mortar crumbs on the roof or top of the crown. Falling mortar bits signal the crown and upper masonry are breaking down. A proper crown repair stops the decay before the stack needs rebuild work.
Our Chimney Cap & Crown Process – Step by Step
- 1
We inspect before we quote. We look at the cap, the crown, the flue tile, and the top course of masonry, and we check the attic side of the chase where we can see it. You get a written report of what we found, not a verbal guess.
- 2
We photograph the problems. Camera inspection and photos included with the report mean you’re not taking our word for a cracked crown or a rusted cap. You can see exactly what needs work and what can safely wait.
- 3
We size and spec the right part. We measure the flue and crown footprint and match the cap to the liner type, selecting from Gelco, Famco, or Copperfield as the job fits. No one-size-fits-all cap forced onto an irregular flue.
- 4
We install and seal. The cap gets fastened through the crown with proper clearance for draft, and crown repairs or coatings are applied to a clean, prepped surface so the bond holds through hot and cold cycles. We check the finished top before we call the job done.
- 5
We clean up and walk you through it. We leave the roof and yard as we found them and review the photos and the report with you. If a flue liner needs HeatShield resurfacing or a DuraFlex liner, we’ll say so plainly and explain why.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in Oak Cliff?
Most chimney cap and crown work in Oak Cliff runs a few hundred dollars for a straightforward single-flue job, and more when a crown rebuild or a custom-fabricated multi-flue cap is involved. A typical cap installation on a single flue runs $185 – $385 depending on cap size, material, and whether the old cap needs to be cut off. Crown repair or a full crown rebuild typically runs $300 – $900, depending on how much of the top needs to be removed and re-poured and how accessible the chimney is. Crown coating over sound masonry usually comes in lower than a rebuild. Multi-flue and custom caps run higher because they’re built to the actual footprint of your stack.
What affects the price: flue count, cap size and material, the condition of the crown and top masonry, roof pitch and access, and whether animal nesting or a liner issue turns up once the cap is off. The written estimate sets the final price, and the estimate itself is free.
To avoid overpaying, ask for photos before you approve anything, and ask whether the crown actually needs a rebuild or whether coating will hold. Nothing is recommended without camera evidence you can see for yourself, and we’ll say plainly when a repair can safely wait until later.
Chimney Cap & Crown Near Oak Cliff – Our Service Area
We work throughout Oak Cliff and nearby areas, including Redbird, Cockrell Hill, Kessler Park, and out toward Duncanville and DeSoto. If you’re closer in, we also cover Uptown, Highland Park, Bluffview, East Dallas, University Park, and Lakewood. Same-day scheduling is often possible depending on the day and parts, and our crews dispatch Sunday through Friday, 7am to 7pm. Learn more about our chimney cap & crown work across the area, or read up on chimney cap & crown for Redbird homes.
Serving Oak Cliff, TX – Our Local Coverage Area
We serve Oak Cliff and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Cap & Crown in Oak Cliff
A chimney cap is the metal hood fitted over the flue opening to keep out rain, birds, and squirrels, and a chimney crown is the sloped masonry or concrete top that sheds water off the chimney’s brickwork. Together they’re the first line of defense against water damage in your chimney. We handle both, plus the liner work underneath, as one job.
A single-flue cap installation usually takes under an hour once we’re on the roof. Crown repairs and coatings take longer because surface prep and curing set the schedule; a rebuild can run most of a day depending on size. We tell you the expected time when we give you the written estimate.
Cap installation typically runs $185 – $385 and crown repair or rebuild typically runs $300 – $900, depending on size, material, and access. The written estimate sets the final price, and the estimate is free with photos so you know what you’re approving. Call (888) 847-8540 for an exact quote.
Yes. We work regularly with Gelco and Famco caps and crowns and with Copperfield components, so we can match the right product to your flue and crown footprint. We also work with DuraFlex liner systems and HeatShield ceramic resurfacing when cap work uncovers a liner issue.
Same-day cap and crown work is often available. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday, and we’re closed on Saturday. Call (888) 847-8540 and we’ll book you into the next opening if it’s outside dispatch hours.
We back our installations with a satisfaction guarantee on the workmanship, and we’ll explain the coverage on your specific cap or crown before the job. If something isn’t right after installation, call us and we’ll make it right. Ask about coverage details when you get your estimate.
Keep the fireplace clear and the area around the chimney inside the house free of anything breakable, and let us know about pets that go in the yard. If you have attic access to the chimney chase, mention it so we can check the interior side. You don’t need to do anything else; we handle the roof and the work.
Schedule Your Chimney Cap & Crown Service in Oak Cliff Today
A failed cap or crown is the cheapest chimney repair you’ll make, and the most expensive one to skip. We’ll inspect the top, show you photos, and quote the work with no pressure. Call (888) 847-8540 for a free, no-obligation estimate. We answer 24/7, with fast dispatch from 7am to 7pm. Find the full range of our Chimney Sweep Oak Cliff services and get booked. Need nearby coverage? See our chimney cap & crown work in Cockrell Hill. If you’re booking a repair alongside your annual visit, our chimney inspection and chimney repair pages cover what else we check on the same trip.
Written by the team at Chimney Sweep Oak Cliff.